John Deere P500 Air Hoe Drill » LandPro Equipment; NY, OH & PA

Sign up for our weekly promotions and events email! We will email no more than once weekly and customers can unsubscribe anytime.


Don't show this again

John Deere P500 Air Hoe Drill

Double tap to zoom



Agronomic benefits

Implementing moisture conservation farming practices

Hydraulic shanks are the workhorses of the P500 Air Seeding tools. They provide consistent depth control for enhanced seed placement, resulting in more even emergence and more uniform crop maturity at harvest. The hydraulic shank seeding tool uses a rigid frame for strength and support. The openers are designed to allow independent downforce for a more uniform depth across the entire width of the frame.


Seed and fertilizer separation are not compromised when seeding with the P500. The opener design allows for banding fertilizer to 15.2 cm (6 in.) within the seedbed and up to 11.4 cm (4.5 in.) of separation between the seed and fertilizer. The deep fertilizer opener doubles as a tillage tool to shatter the hard pan for improved root development, water infiltration, and seedbed warmth.

John Deere P500 key agronomic benefits:

  • Freshly exposed black soil is able to attract the sun’s radiation, warming the ground
    • Warmer soil temperature promotes early germination
  • Good seed to soil contact
    • Necessary for germination to take place
  • Seed row has been cleared of any residue or straw
    • Provides a clear growth path
    • Allows for abundant access to sunlight once the seedling has emerged from the ground.
  • Starter nutrients placed next to seed on the shelf, promote early plant growth.
    • As the plant strengthens, roots are sent off through mellow dirt into higher rate fertilizer just below the shelf
  • The trench left behind helps in cupping rainfall and preventing water run off
    • Provides more moisture for the plant during dry years

Depth control

When seeding small grains and oil seeds, consistent seed and fertilizer depth control are critical for even emergence. By using two independent hydraulic accumulator force systems, the John Deere opener allows the seed and fertilizer opener trip forces to be set independent of each other.


The use of independent hydraulic accumulator technology, combined with the separate packer wheel force, allows seed-depth gauging to be done on each individual row by the press wheel.


The breakout force for the fertilizer shank is set by adjusting the large accumulator pressure. The press wheel and seed opener down force are set by adjusting pressure on the smaller accumulator. Trip force for the seed opener is set by adjusting a spring shock attached to the seed opener.


Seeding with the P500 gives uncompromised control for seeding operation. Producers are able to maintain safe seed and fertilizer separation with depth placement up to 15.2 cm (6 in.) for the fertilizer.


Setting the fertilizer and seed depth is a very simple process. Fertilizer depth across the machine is set by the frame. Adjusting the seed tube up or down on each individual row-unit sets the preferred seed depth. The tube is positively locked tight by the freshly designed cam system.


Rear cart duals are recommended to help reduce deflection on the front hitch of the tool with a tow-between cart. Adding air pressure, without exceeding maximum psi, will also assist with reducing deflection.


For the 23.2-m (76-ft) P576 TruSet technology will control depth and pressure. Read more about TruSet here.

Fertilizer placement

Whether using dry, liquid, or anhydrous ammonia, the John Deere P500 opener has the options that fit the application needs.

Additional information for code 1235: the mud-proof combination of dry-fertilizer tube and tip, code 1235, is available for those applying dry fertilizers only. This is recommended for running in sticky, heavy clay-type soils. However, it works well in all soil types to prevent mud from plugging the fertilizer tube opening. This opener is included as base equipment.


If seeding with dry fertilizer only, this option is highly recommended. The fertilizer exits the tube at a lower point, allowing growers desiring to place fertilizer at shallower depths more consistently.


The lower fertilizer exit point also allows the fertilizer to get to the bottom of the trench when more fertilizer and seed separation is desired, and for those light soils that tend to cave in the trench before the fertilizer is placed.

TruSet™ depth and pressure control for 23.2-m (76-ft) P576

Exclusive TruSet depth and pressure control has taken adjustability on the 23.2-m (76-ft) P576 to a whole new level. Rather than using manual valve handles, pressure control dials on the monitor let operators make incremental adjustments to trip force and packing pressure conveniently from inside the tractor cab. This also saves time and makes it easier to adapt to changing field conditions.


Controls on the GreenStar 3 2630 Display also allow operators to predetermine a targeted seeding and fertilizer depth. Changes to target maximum and minimum working depth can be made easily on the same run screen. A flick adjustment feature will move openers up or down in short increments if desired. There is no longer a need to get out of the cab to add or remove shims and spacers for depth changes. Plus, TruSet makes side-to-side frame leveling easier. It adjusts at the press of a button on the GreenStar 3 2630 Display.

There is a rotary position sensor under the TruSet plate. In the lower right-hand corner is the valve that regulates the flow of oil to and from the cylinder. There is a sensor associated with each wheel module – or six per machine.


Competitive tractors require an add-on selective control valve (SCV) kit for TruSet to function properly.

RelativeFlow™ Blockage sensing

With the RelativeFlow blockage system, operators can see the flow rate of both seed and fertilizer from inside the tractor cab. Sensors on delivery hoses monitor the relative rate of product flow. An easy-to-read display clearly visualizes relative product flow across the drill, from opener to opener. This exclusive technology gives a better view of what is happening across the tool in order to spot problems before blockage occurs.


RelativeFlow Blockage is available on the following models:

  • 1890 - 15.2-m (50-ft) and 18.3-m (60-ft)
  • P540 - 12.2-m (40-ft)
  • P556 - 17.1-m (56-ft)
  • P576 - 23.2-m (76-ft)
  • N560F - 18.3-m (60-ft)
  • N500C - all widths
  • N530F - 9.1-m (30-ft)
  • N540F - 12.2-m (40-ft)
  • N543F - 13.1-m (43-ft)


For complete details and information reference, the owner’s manual.

Blockage alarm delays can be set up by clicking on the advanced settings button from the blockage set-up screen.

  • A blockage delay is how long a blockage should occur before an alarm is sounded.
  • The blockage alarm reminder is how often the alarm should sound when a blockage occurs.
  • The meter on delay is the time from when the meter is turned on until the blockage sensor should start monitoring for blockage.
  • The meter off delay is the time from when the meter is turned off until the blockage sensor should start monitoring to verify no flow.


For more detailed information, see the owner’s manual.

Row spacing options

Paired row vs. side banded

The P500 has two cast seed boots available. Depending on a grower’s seed and fertilizer placement preference in different soils or different crops, the P500 can meet the user’s needs. The cast opener was designed with simplicity in mind. One tube is all that is necessary. Switching from single to paired row has never been easier; simply remove the two bolts holding the cast opener in place, remove the opener, and replace with the new opener.


Paired row

With shanks on 30.5-cm (12-in.) spacing, paired rows can be planted with 22.9-cm (9-in.) spacing. Seed is banded in two rows above and to the sides of the furrow. Total tillage in this zone is 7.6-cm (3-in.) wide with about 25 percent seedbed utilization (SBU).


Seed is laid on a 2-cm (0.75-in.) shelf while fertilizer is placed in a 2.5-cm (1-in.) band between and below the two seed rows.


With paired row placement, the crop is able to access the fertilizer when it needs it. The separation is enough to safely keep the seed from burning. The P500 provides a well-prepared seedbed for quick emergence and quicker canopy, which will help eliminate weeds. If the operator is looking to swath wider rows, support the heavy green crop. 

Side banded

If the seeding operation calls for side banding, the P500 is the needed tool. The side-banding seed tube places the seed on a firm bed of soil above and to the side of fertilizer as required. There are 30.5-cm (12-in.) rows across the machine with positive separation between seed and fertilizer up to 11.4 cm (4.5 in.). As the seed germinates and begins to emerge, its roots will be 7.6-cm to 10.2-cm (3-in. to 4-in.) deep and into the nutrient zone.


John Deere recognizes not all seeding conditions are identical and, with the P500, offers solutions to meet seed and fertilizer placement needs.

High-flotation kit for 23.2-m (76-ft) P576 Precision Hoe Drill

For small-grain producers who want to increase flotation and reduce compaction, a high-flotation kit is available for the 23.2-m (76-ft) P576 Precision Hoe Drill.

Customer value

The high-flotation kit for the 23.2-m (76-ft) P576 Precision Hoe Drill provides producers with excellent performance, a boost in uptime, and reduced cost of operation. The high-flotation package consists of two main components: larger front mainframe tires and an in-frame lift assist system. This complete package results in:

  • 91.7 percent increase in flat plate area for front wheels
  • 60 percent improvement in stuck factor for wheels
  • Reduction in tire inflation pressures
  • Reduction in ground pressures
  • Ability to get in the field sooner if desired
How it works

The high-flotation kit works in two ways:

  1. The larger front mainframe tires add an increase in flotation to the front of the machine.
  2. The in-frame lift assist system utilizes the power beyond circuit and a hydraulic valve block to set system pressure, utilizing accumulators to raise and lower the system. The in-frame system has new components to be installed within the existing mainframe to increase flotation and allow the machine weight to be spread across additional tire surface area.
High-flotation kit components

Larger front mainframe tires:

  Standard front tires High-flotation front tires
Tire 440/55R18 550/45-22.5
Load capacity 4377.2 kg (9650 lb) 3646.9 kg (8040 lb)
Inflation pressure 5 bar (73 psi) 1.5 bar (22 psi)
Outside diameter 94.2 cm (37.1 in.) 106.9 cm (42.1 in.)
Width 43.4 cm (17.1 in.) 55.1 cm (21.7 in.)
Static loaded radius 42.2 cm (16.6 in.) 47 cm (18.5 in.)
Flat plate area 1006.5 cm2 (156 sq in.) 1929 cm2 (299 sq in.)



Lift assist system:

This kit does not include any 440/55R18 tires for the lift assist system. The producer will use the 440/55R18 tires from the mainframe front that will be replaced by 550/45-22.5 tires as part of the kit pre-delivery inspection (PDI) process.


This kit is compatible with all 23.2-m (76-ft) P576 Precision Hoe Drills.


This kit will be initially offered as a product enhancement program (PEP). See PEP #18AX461 for more details.


Attachment Description
MPA10950 23.2-m (76-ft) P576 High-flotation PEP kit
NOTE: Includes larger front tires and assembly and lift assist system. Does not include 440/55R18 tires.


Mainframe and wing wheel scrapers

The mainframe and wing wheel scrapers have been redesigned to better meet producer needs. These scrapers are included in the high-flotation kit. BA33708 can also be ordered separately if the grower does not want the flotation kit.


Attachment Description
BA33708 Main frame and wing wheel scrapers
NOTE: Order one kit per 23.2-m (76-ft) P576 Drill.


Sorry, currently there are no specs but check back with us later.


Let us help you get moving.