Mounting a tablet, cell phone, or beverage can be easily done with these solutions. These strong and simple-to-use solutions keep all important items right where they are wanted.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

 

Carpet floor mat

Reduce cab noise and increase comfort with fabric flooring in the cab. This snag-resistant mat is color-matched to the existing tractor cab interior and is easily removed and installed for quick cleaning. The die-cut carpet lays directly over the rubber floor in the cab and is a precise fit. This feature is included in the Ultimate Comfort and Convenience package.

 

Foot throttle kit

The foot throttle kit adds the ability to control engine rpm with the right foot. This allows the operator to control ground speed like an automobile while driving or to make power adjustments to adjust hydraulic flow for operating certain implements.

 

 

Foot decelerator kit

The foot decelerator kit adds the ability to decrease vehicle speed with the right foot. This allows the operator to progressively slow ground speed during precise maneuvering such as at headland turns or around objects without adjusting the set speed. This is exceptionally helpful when operating at full speed for long periods of time.

 

Footrests

The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.

 

The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.

 

Features:

• Direct bolt-on factory finish – no drilling or cutting required
• Heavy gauge steel to support any operator
• Color-matched rubber surfaces for comfort and vibration reduction
• Model year 2022 and newer are compatible with extension and adjustment kit (BRE10511)

 

Sun shade

The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.

 

Storage container with lid/ashtray

This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right side window.

 

Leather-wrapped steering wheel

Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.

 

Refrigerator

The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists and no software is required to complete the install.

 

Rearview mirror (internal)

The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.

 

Cab power inverter

These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update. 

Six-outlet octagonal power strip with pre-installed round convenience outlet (flat pins)

The six-outlet octagonal power strip with pre-installed round convenience outlet is available for field installation for operators that prefer this traditional connection style. This solution can support up to 30 amps of power from the existing, shared 30-amp fused power circuit of the cab. It also provides operators with the same connection in the cab to power equipment they may already have or share with other machines over several generations. The above image shows one mounting option using vertical rail kit BRE10464.

Three-pin octagonal to three-pin round convenience outlet (flat pins) single device adapter

For operators who prefer the six-way power strip connection type but only have one or two accessories to connect in the cab, this single adapter solution is available. The single jumper harness converts one prewired three-pin octagonal style connector into a three-pin round outlet. This solution allows a more economically priced conversion for producers who do not need the full power strip solution.

A similar design for European power connector style is available as RE596960 three-pin octagonal to three-pin round/triangular convenience outlet (round pins) single device adapter.

Harness adapter for citizen band (CB) power connection

Operators using business band/citizen band (CB) radio in their cab will find the model year 2020 7R and 8R Tractors come prewired with antenna coax, power connector, and an NMO antenna base. When wiring the business band radio, the pig-tail connector can be hard wired to the constant power, switched power, and ground wires. It can then be connected directly to the cab base harness power connection point without any cutting or modification, eliminating any need to run new power wires from the fuse panel. These connection points are located under the upper right console next to the open storage tray and mirror/wiper controls, making for a clean install in the cab. The operator only needs to supply the radio unit and NMO style antenna of their choice.

 

Amp-to-flying leads power connector

This adapter allows users to connect aftermarket displays to the universal amp power connector. The female three-socket connector has three flying leads that can be fused to the display harness. Once installed, the display harness will connect to the three-prong amp power adapter in the cab or to the RE67015 outlet adapter.

 

Amp-to-John Deere power outlet adapter

This adapter allows users to connect an amp-style, three-socket connector to the John Deere-style power strip connection type. Use this adapter to quickly and easily connect amp-style power accessories to older, vintage tractors that do not have an amp-style outlet already in the cab without cutting wire harnesses. This adapter can be kept connected into the John Deere-style power strip if users are regularly moving a unique display between vintage and newer tractors in the fleet.

 

External StarFire™ mounting bracket

The model year 2020 large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or Starfire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.

 

Front license plate mounting bracket

This bracket solution provides a mounting location for countries that require a roadway license mounted to the front of the vehicle. This bracket bolts into place above the front window wiper motor and is also compatible with the external StarFire mounting bracket.

 

Vandal protection door locks with custom key

Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.

 

Joystick (multifunction lever)

This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.

 

Subwoofer and tweeter kit

Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.

 

The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.

 

Touchscreen radio relocation kit

Move the touchscreen radio from the factory-installed location (upper right radio bezel) to several other locations with this relocation kit. The kit includes a new headliner bezel, brackets, harness jumper, hardware, and instructions to move the touchscreen unit from its factory location. This kit is for relocation mounting only and does not include the radio unit.

 

Features:

• Allows touchscreen radio to be mounted on rollover protective structure (ROPS) and off the CommandARM bracket or on several other accessory mounting bracket rails sold separately
• Fine-tune the position adjustment with the locking knob on the tie rod

 

Touchscreen video camera upgrade kit

Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.

 

NOTE: Reference the Cab Mounting Solutions sales guide to view the wide range of mounting accessories for the cab.

Mounting a tablet, cell phone, or beverage can be easily done with these solutions. These strong and simple-to-use solutions keep all important items right where they are wanted.

Use the tables below to find all the parts needed to connect GreenStar displays physically and electronically.

 

For GreenStar 2 CommandCenter™ 2600/GreenStar 3 2630 Displays:

Mounting style	Display mount (ball)	Tie-rod assembly	Rail mount (ball)
Clamp	PF11019 plus two 19M8648	RE574454	AXE59372
10-mm (0.4-in.) threaded	PF11019 plus two 19M8648	PF80459	RE576490
Single location bracket	RE558242

The clamp-style mount with GreenStar monitor is not recommended with the vertical rail (BRE10575).

 

NOTE: Also order power harness (PF90686) and Ethernet cable (PFP12950). Optional protective film for screen (PF90596) is also available.

For 4240 /4640 Universal Display and Extended Monitor:

Mounting style	Display mount (ball)	Tie-rod assembly	Rail mount (ball)
Clamp	AL212683 plus four 19M8648		AXE59372
10-mm (0.4-in.) threaded	UC17356 plus four 19M8648	PF80459	RE576490
Single location bracket	RE558242

The clamp-style mount with GreenStar monitor is not recommended with the vertical rail (BRE10575). 

NOTE: Also order power harness (PFP12435) and Ethernet cable (RE573617). Optional protective film for screen (PF90596) is also available.

This unique bracket connects to the right side of the CommandARM. It is compatible with the cell phone mount (BRE10015), tablet mount (BRE10255), and more. It is also compatible with the touchscreen radio relocation kit (BXX11045) for Premium and Ultimate Comfort and Convenience packages.

The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.

 

The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.

 

Features:

• Direct bolt-on factory finish – no drilling or cutting required
• Heavy gauge steel to support any operator
• Color-matched rubber surfaces for comfort and vibration reduction
• Model year 2022 and newer are compatible with the extension and adjustment kit (BRE10511)

The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.

 

The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.

 

Features:

• Direct bolt-on factory finish – no drilling or cutting required
• Heavy gauge steel to support any operator
• Color-matched rubber surfaces for comfort and vibration reduction
• Model year 2022 and newer are compatible with the extension and adjustment kit (BRE10511)

Keep accessory and monitor wiring neatly contained with these moveable harness hooks. These hooks are specifically designed to easily snap into the factory headliner rail and BRE10574 window mounting bracket and rail with no tools and can be moved as needed. These hooks allow accessory wiring to routed together for a clean look and maximized visibility.

Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.

There are a variety of additional mounting part solutions available through John Deere to resolve unique mounting configuration needs. The table below includes several additional parts (not shown above) to aid in many different mounting needs.

Use the tables below to find all the parts needed to connect GreenStar displays physically and electronically.

 

For GreenStar 2 CommandCenter™ 2600/GreenStar 3 2630 Displays:

Mounting style	Display mount (ball)	Tie-rod assembly	Rail mount (ball)
Clamp	PF11019 plus two 19M8648	RE574454	AXE59372
10-mm (0.4-in.) threaded	PF11019 plus two 19M8648	PF80459	RE576490
Single location bracket	RE558242

The clamp-style mount with GreenStar monitor is not recommended with the vertical rail (BRE10575).

 

NOTE: Also order power harness (PF90686) and Ethernet cable (PFP12950). Optional protective film for screen (PF90596) is also available.

For 4240 /4640 Universal Display and Extended Monitor:

Mounting style	Display mount (ball)	Tie-rod assembly	Rail mount (ball)
Clamp	AL212683 plus four 19M8648		AXE59372
10-mm (0.4-in.) threaded	UC17356 plus four 19M8648	PF80459	RE576490
Single location bracket	RE558242

The clamp-style mount with GreenStar monitor is not recommended with the vertical rail (BRE10575). 

NOTE: Also order power harness (PFP12435) and Ethernet cable (RE573617). Optional protective film for screen (PF90596) is also available.

The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists, and no software is required to complete the install.

A large steel bracket, which spans the entire right-side window, mounts directly to the cab frame for rigidity and strength. The headliner mounting rail (included in this kit) is bolted to the steel bracket. This solution enables the operator to configure and reconfigure monitors and accessories without changing mounting solutions from either location. This rail accommodates clamp-style and T-slot style mount solutions (purchased separately).

 

• Spans the entire right-side window.
• Uses the same factory headliner mounting rail part number (R558980) for easy reconfiguring of accessories.
• Aluminum mounting rail mounts to either the top or underside of the steel bracket, allowing even more options and maximizing visibility preferences.
• Compatible with AXE59372 (clamp-style mount) and BRE10482 and BRE10483 (T-slot ball mounts).

This kit provides additional (premium upgrade) controls for operating the rear hitch from the operator's seat.

Mounting a tablet, cell phone, or beverage can be easily done with these solutions. These strong and simple-to-use solutions keep all important items right where they are wanted.

A shorter, 260-mm (10.25-in.) aluminum mounting rail is available. The kit includes all the hardware needed to mount in up to five vertical locations, including upper and lower right-side A-post rollover protective structure (ROPS), upper right-side C-post ROPS, and upper left rear C-post ROPS. It is compatible with both clamp-style and t-slotted ball mounts (purchased separately).

 

• Up to five vertical locations supported with this one rail (kit contains one rail and mounting hardware).
• Uses the same factory headliner mounting rail shape for ease of operator adjustment and preferences.
• Works in combination with other accessory bracket solutions.
• Compatible with AXE59372 (clamp-style mount) and BRE10482 and BRE10483 (T-slot ball mounts).

This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.

This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right-side window.

The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.

Mounting a tablet, cell phone, or beverage can be easily done with these solutions. These strong and simple-to-use solutions keep all important items right where they are wanted.

Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.

This adapter allows users to connect an amp-style, three-socket connector to the John Deere-style power strip connection type. Use this adapter to quickly and easily connect amp-style power accessories to older, vintage tractors that do not have an amp-style outlet already in the cab without cutting wire harnesses. This adapter can be kept connected into the John Deere-style power strip if users are regularly moving a unique display between vintage and newer tractors in the fleet.

The nine-pin electrical connector is required to allow TouchSet™ depth control to be used with implements with this feature. The harness provides a position input to the tractor selective control valve (SCV) unit, enabling the TouchSet system.
 
This feature allows the operator to adjust height and depth of remote lift cylinders by using the TouchSet controls in the cab.

This adapter allows users to connect aftermarket displays to the universal amp power connector. The female three-socket connector has three flying leads that can be fused to the display harness. Once installed, the display harness will connect to the three-prong amp power adapter in the cab or to the RE67015 outlet adapter.

The ISO cab implement CAN bus adapter is available to connect any ISO compliant implement or device to an 8R, 8RT, 9R, 9RT, and 9RX (including Scraper Special) Tractor. These connectors are commonly used for planter frame control boxes. 

 

Refer to the operator's manual, sections 16 (CommandCenter™) and 25 (Operator Station), for additional information on ISO implements.

 

NOTE: If the harness is not in use, unplug it from the ISO 11783 location or plug the four-pin connectors together on the harness. If neither of these are done, implement CAN communication errors occur.

The implement switch indicates to the CommandCenter™ system when the implement is raised or lowered, providing accurate data collection when using a performance monitor.

The model year 2020 and newer large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or StarFire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.

This cable connects the cornerpost Ethernet connector (square) to the GreenStar™ 3 2630 Display Ethernet connector (round). It is required for used with Remote Display Access (RDA), Wireless Data Transfer (WDT), and Machine Sync.

 

The square-to-round connector cable is 80-cm (31.5-in.) long.

Increase drawbar capability by upgrading to this heavy-duty Category 4 drawbar, capable of 4990-kg (11,000-lb) vertical load capacity. The kit includes drawbar, safety chain strap, drop pin, and hardware.

Scraper drawbars are available for high horsepower tractors to connect earthmoving and some specialized equipment.

 

Row-crop tractor scraper drawbars are available in two styles: yoke and quick attach. The quick-attach drawbar connects to all John Deere 11.5-m³ (15-cu yd) scraper models manufactured since 2005. The yoke drawbar connects to all John Deere 11.5-m³ (15-cu yd) scraper models manufactured since 2001. 

Scraper drawbars are available for high horsepower tractors to connect earthmoving and some specialized equipment.

 

Row-crop tractor scraper drawbars are available in two styles: yoke and quick attach. The quick-attach drawbar connects to all John Deere 11.5-m³ (15-cu yd) scraper models manufactured since 2005. The yoke drawbar connects to all John Deere 11.5-m³ (15-cu yd) scraper models manufactured since 2001. 

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

 

Carpet floor mat

Reduce cab noise and increase comfort with fabric flooring in the cab. This snag-resistant mat is color-matched to the existing tractor cab interior and is easily removed and installed for quick cleaning. The die-cut carpet lays directly over the rubber floor in the cab and is a precise fit. This feature is included in the Ultimate Comfort and Convenience package.

 

Foot throttle kit

The foot throttle kit adds the ability to control engine rpm with the right foot. This allows the operator to control ground speed like an automobile while driving or to make power adjustments to adjust hydraulic flow for operating certain implements.

 

 

Foot decelerator kit

The foot decelerator kit adds the ability to decrease vehicle speed with the right foot. This allows the operator to progressively slow ground speed during precise maneuvering such as at headland turns or around objects without adjusting the set speed. This is exceptionally helpful when operating at full speed for long periods of time.

 

Footrests

The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.

 

The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.

 

Features:

• Direct bolt-on factory finish – no drilling or cutting required
• Heavy gauge steel to support any operator
• Color-matched rubber surfaces for comfort and vibration reduction
• Model year 2022 and newer are compatible with extension and adjustment kit (BRE10511)

 

Sun shade

The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.

 

Storage container with lid/ashtray

This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right side window.

 

Leather-wrapped steering wheel

Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.

 

Refrigerator

The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists and no software is required to complete the install.

 

Rearview mirror (internal)

The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.

 

Cab power inverter

These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update. 

Six-outlet octagonal power strip with pre-installed round convenience outlet (flat pins)

The six-outlet octagonal power strip with pre-installed round convenience outlet is available for field installation for operators that prefer this traditional connection style. This solution can support up to 30 amps of power from the existing, shared 30-amp fused power circuit of the cab. It also provides operators with the same connection in the cab to power equipment they may already have or share with other machines over several generations. The above image shows one mounting option using vertical rail kit BRE10464.

Three-pin octagonal to three-pin round convenience outlet (flat pins) single device adapter

For operators who prefer the six-way power strip connection type but only have one or two accessories to connect in the cab, this single adapter solution is available. The single jumper harness converts one prewired three-pin octagonal style connector into a three-pin round outlet. This solution allows a more economically priced conversion for producers who do not need the full power strip solution.

A similar design for European power connector style is available as RE596960 three-pin octagonal to three-pin round/triangular convenience outlet (round pins) single device adapter.

Harness adapter for citizen band (CB) power connection

Operators using business band/citizen band (CB) radio in their cab will find the model year 2020 7R and 8R Tractors come prewired with antenna coax, power connector, and an NMO antenna base. When wiring the business band radio, the pig-tail connector can be hard wired to the constant power, switched power, and ground wires. It can then be connected directly to the cab base harness power connection point without any cutting or modification, eliminating any need to run new power wires from the fuse panel. These connection points are located under the upper right console next to the open storage tray and mirror/wiper controls, making for a clean install in the cab. The operator only needs to supply the radio unit and NMO style antenna of their choice.

 

Amp-to-flying leads power connector

This adapter allows users to connect aftermarket displays to the universal amp power connector. The female three-socket connector has three flying leads that can be fused to the display harness. Once installed, the display harness will connect to the three-prong amp power adapter in the cab or to the RE67015 outlet adapter.

 

Amp-to-John Deere power outlet adapter

This adapter allows users to connect an amp-style, three-socket connector to the John Deere-style power strip connection type. Use this adapter to quickly and easily connect amp-style power accessories to older, vintage tractors that do not have an amp-style outlet already in the cab without cutting wire harnesses. This adapter can be kept connected into the John Deere-style power strip if users are regularly moving a unique display between vintage and newer tractors in the fleet.

 

External StarFire™ mounting bracket

The model year 2020 large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or Starfire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.

 

Front license plate mounting bracket

This bracket solution provides a mounting location for countries that require a roadway license mounted to the front of the vehicle. This bracket bolts into place above the front window wiper motor and is also compatible with the external StarFire mounting bracket.

 

Vandal protection door locks with custom key

Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.

 

Joystick (multifunction lever)

This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.

 

Subwoofer and tweeter kit

Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.

 

The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.

 

Touchscreen radio relocation kit

Move the touchscreen radio from the factory-installed location (upper right radio bezel) to several other locations with this relocation kit. The kit includes a new headliner bezel, brackets, harness jumper, hardware, and instructions to move the touchscreen unit from its factory location. This kit is for relocation mounting only and does not include the radio unit.

 

Features:

• Allows touchscreen radio to be mounted on rollover protective structure (ROPS) and off the CommandARM bracket or on several other accessory mounting bracket rails sold separately
• Fine-tune the position adjustment with the locking knob on the tie rod

 

Touchscreen video camera upgrade kit

Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.

 

NOTE: Reference the Cab Mounting Solutions sales guide to view the wide range of mounting accessories for the cab.

Increase electrical output and charging potential by upgrading from the standard factory 250-amp alternator to a 330-amp alternator. This alternator allows producers to add additional electrical demands on their tractor or implement without putting strain on the charging system. The 330-amp alternator also allows the electrical system to charge faster (with increased electrical demand), even at lower engine rpm.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

 

Carpet floor mat

Reduce cab noise and increase comfort with fabric flooring in the cab. This snag-resistant mat is color-matched to the existing tractor cab interior and is easily removed and installed for quick cleaning. The die-cut carpet lays directly over the rubber floor in the cab and is a precise fit. This feature is included in the Ultimate Comfort and Convenience package.

 

Foot throttle kit

The foot throttle kit adds the ability to control engine rpm with the right foot. This allows the operator to control ground speed like an automobile while driving or to make power adjustments to adjust hydraulic flow for operating certain implements.

 

 

Foot decelerator kit

The foot decelerator kit adds the ability to decrease vehicle speed with the right foot. This allows the operator to progressively slow ground speed during precise maneuvering such as at headland turns or around objects without adjusting the set speed. This is exceptionally helpful when operating at full speed for long periods of time.

 

Footrests

The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.

 

The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.

 

Features:

• Direct bolt-on factory finish – no drilling or cutting required
• Heavy gauge steel to support any operator
• Color-matched rubber surfaces for comfort and vibration reduction
• Model year 2022 and newer are compatible with extension and adjustment kit (BRE10511)

 

Sun shade

The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.

 

Storage container with lid/ashtray

This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right side window.

 

Leather-wrapped steering wheel

Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.

 

Refrigerator

The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists and no software is required to complete the install.

 

Rearview mirror (internal)

The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.

 

Cab power inverter

These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update. 

Six-outlet octagonal power strip with pre-installed round convenience outlet (flat pins)

The six-outlet octagonal power strip with pre-installed round convenience outlet is available for field installation for operators that prefer this traditional connection style. This solution can support up to 30 amps of power from the existing, shared 30-amp fused power circuit of the cab. It also provides operators with the same connection in the cab to power equipment they may already have or share with other machines over several generations. The above image shows one mounting option using vertical rail kit BRE10464.

Three-pin octagonal to three-pin round convenience outlet (flat pins) single device adapter

For operators who prefer the six-way power strip connection type but only have one or two accessories to connect in the cab, this single adapter solution is available. The single jumper harness converts one prewired three-pin octagonal style connector into a three-pin round outlet. This solution allows a more economically priced conversion for producers who do not need the full power strip solution.

A similar design for European power connector style is available as RE596960 three-pin octagonal to three-pin round/triangular convenience outlet (round pins) single device adapter.

Harness adapter for citizen band (CB) power connection

Operators using business band/citizen band (CB) radio in their cab will find the model year 2020 7R and 8R Tractors come prewired with antenna coax, power connector, and an NMO antenna base. When wiring the business band radio, the pig-tail connector can be hard wired to the constant power, switched power, and ground wires. It can then be connected directly to the cab base harness power connection point without any cutting or modification, eliminating any need to run new power wires from the fuse panel. These connection points are located under the upper right console next to the open storage tray and mirror/wiper controls, making for a clean install in the cab. The operator only needs to supply the radio unit and NMO style antenna of their choice.

 

Amp-to-flying leads power connector

This adapter allows users to connect aftermarket displays to the universal amp power connector. The female three-socket connector has three flying leads that can be fused to the display harness. Once installed, the display harness will connect to the three-prong amp power adapter in the cab or to the RE67015 outlet adapter.

 

Amp-to-John Deere power outlet adapter

This adapter allows users to connect an amp-style, three-socket connector to the John Deere-style power strip connection type. Use this adapter to quickly and easily connect amp-style power accessories to older, vintage tractors that do not have an amp-style outlet already in the cab without cutting wire harnesses. This adapter can be kept connected into the John Deere-style power strip if users are regularly moving a unique display between vintage and newer tractors in the fleet.

 

External StarFire™ mounting bracket

The model year 2020 large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or Starfire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.

 

Front license plate mounting bracket

This bracket solution provides a mounting location for countries that require a roadway license mounted to the front of the vehicle. This bracket bolts into place above the front window wiper motor and is also compatible with the external StarFire mounting bracket.

 

Vandal protection door locks with custom key

Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.

 

Joystick (multifunction lever)

This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.

 

Subwoofer and tweeter kit

Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.

 

The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.

 

Touchscreen radio relocation kit

Move the touchscreen radio from the factory-installed location (upper right radio bezel) to several other locations with this relocation kit. The kit includes a new headliner bezel, brackets, harness jumper, hardware, and instructions to move the touchscreen unit from its factory location. This kit is for relocation mounting only and does not include the radio unit.

 

Features:

• Allows touchscreen radio to be mounted on rollover protective structure (ROPS) and off the CommandARM bracket or on several other accessory mounting bracket rails sold separately
• Fine-tune the position adjustment with the locking knob on the tie rod

 

Touchscreen video camera upgrade kit

Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.

 

NOTE: Reference the Cab Mounting Solutions sales guide to view the wide range of mounting accessories for the cab.

These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

 

Carpet floor mat

Reduce cab noise and increase comfort with fabric flooring in the cab. This snag-resistant mat is color-matched to the existing tractor cab interior and is easily removed and installed for quick cleaning. The die-cut carpet lays directly over the rubber floor in the cab and is a precise fit. This feature is included in the Ultimate Comfort and Convenience package.

 

Foot throttle kit

The foot throttle kit adds the ability to control engine rpm with the right foot. This allows the operator to control ground speed like an automobile while driving or to make power adjustments to adjust hydraulic flow for operating certain implements.

 

 

Foot decelerator kit

The foot decelerator kit adds the ability to decrease vehicle speed with the right foot. This allows the operator to progressively slow ground speed during precise maneuvering such as at headland turns or around objects without adjusting the set speed. This is exceptionally helpful when operating at full speed for long periods of time.

 

Footrests

The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.

 

The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.

 

Features:

• Direct bolt-on factory finish – no drilling or cutting required
• Heavy gauge steel to support any operator
• Color-matched rubber surfaces for comfort and vibration reduction
• Model year 2022 and newer are compatible with extension and adjustment kit (BRE10511)

 

Sun shade

The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.

 

Storage container with lid/ashtray

This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right side window.

 

Leather-wrapped steering wheel

Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.

 

Refrigerator

The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists and no software is required to complete the install.

 

Rearview mirror (internal)

The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.

 

Cab power inverter

These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update. 

Six-outlet octagonal power strip with pre-installed round convenience outlet (flat pins)

The six-outlet octagonal power strip with pre-installed round convenience outlet is available for field installation for operators that prefer this traditional connection style. This solution can support up to 30 amps of power from the existing, shared 30-amp fused power circuit of the cab. It also provides operators with the same connection in the cab to power equipment they may already have or share with other machines over several generations. The above image shows one mounting option using vertical rail kit BRE10464.

Three-pin octagonal to three-pin round convenience outlet (flat pins) single device adapter

For operators who prefer the six-way power strip connection type but only have one or two accessories to connect in the cab, this single adapter solution is available. The single jumper harness converts one prewired three-pin octagonal style connector into a three-pin round outlet. This solution allows a more economically priced conversion for producers who do not need the full power strip solution.

A similar design for European power connector style is available as RE596960 three-pin octagonal to three-pin round/triangular convenience outlet (round pins) single device adapter.

Harness adapter for citizen band (CB) power connection

Operators using business band/citizen band (CB) radio in their cab will find the model year 2020 7R and 8R Tractors come prewired with antenna coax, power connector, and an NMO antenna base. When wiring the business band radio, the pig-tail connector can be hard wired to the constant power, switched power, and ground wires. It can then be connected directly to the cab base harness power connection point without any cutting or modification, eliminating any need to run new power wires from the fuse panel. These connection points are located under the upper right console next to the open storage tray and mirror/wiper controls, making for a clean install in the cab. The operator only needs to supply the radio unit and NMO style antenna of their choice.

 

Amp-to-flying leads power connector

This adapter allows users to connect aftermarket displays to the universal amp power connector. The female three-socket connector has three flying leads that can be fused to the display harness. Once installed, the display harness will connect to the three-prong amp power adapter in the cab or to the RE67015 outlet adapter.

 

Amp-to-John Deere power outlet adapter

This adapter allows users to connect an amp-style, three-socket connector to the John Deere-style power strip connection type. Use this adapter to quickly and easily connect amp-style power accessories to older, vintage tractors that do not have an amp-style outlet already in the cab without cutting wire harnesses. This adapter can be kept connected into the John Deere-style power strip if users are regularly moving a unique display between vintage and newer tractors in the fleet.

 

External StarFire™ mounting bracket

The model year 2020 large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or Starfire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.

 

Front license plate mounting bracket

This bracket solution provides a mounting location for countries that require a roadway license mounted to the front of the vehicle. This bracket bolts into place above the front window wiper motor and is also compatible with the external StarFire mounting bracket.

 

Vandal protection door locks with custom key

Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.

 

Joystick (multifunction lever)

This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.

 

Subwoofer and tweeter kit

Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.

 

The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.

 

Touchscreen radio relocation kit

Move the touchscreen radio from the factory-installed location (upper right radio bezel) to several other locations with this relocation kit. The kit includes a new headliner bezel, brackets, harness jumper, hardware, and instructions to move the touchscreen unit from its factory location. This kit is for relocation mounting only and does not include the radio unit.

 

Features:

• Allows touchscreen radio to be mounted on rollover protective structure (ROPS) and off the CommandARM bracket or on several other accessory mounting bracket rails sold separately
• Fine-tune the position adjustment with the locking knob on the tie rod

 

Touchscreen video camera upgrade kit

Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.

 

NOTE: Reference the Cab Mounting Solutions sales guide to view the wide range of mounting accessories for the cab.

Increase visibility in the front, rear, or both areas of the tractor with a video camera system upgrade. If a Select or Premium Visibility package was ordered from the factory, producers can still upgrade to a front and/or rear video camera by simply purchasing the camera parts and mounting bezels.

 

The front camera mounts into the grill, and the rear camera mounts above the rear window in the roof assembly. These video cameras are a direct harness plug-in and do not require a software update. Video feed comes through the display on the CommandARM™ console.

Increase visibility in the front, rear, or both areas of the tractor with a video camera system upgrade. If a Select or Premium Visibility package was ordered from the factory, producers can still upgrade to a front and/or rear video camera by simply purchasing the camera parts and mounting bezels.

 

The front camera mounts into the grill, and the rear camera mounts above the rear window in the roof assembly. These video cameras are a direct harness plug-in and do not require a software update. Video feed comes through the display on the CommandARM™ console.

Engine block coolant heater kits are recommended for tractors frequently started in cold weather. Mount this kit into the engine block after removing a freeze plug. The heater cord is then connected to an electrical supply and keeps the coolant in the engine warm. For best results, plug in the heater when coolant is already warm from engine operation.

The engine ether kit is recommended for tractors frequently started in cold weather. This kit injects ether into the air intake manifold, allowing quick combustion even in below-average temperatures.

IPM

NOTE: IPM is only available for Final Tier 4 (FT4)/Stage V engines, and not for Stage II or Tier 3/Stage IIIA engines.

 

This feature is for many typical farming operations that use the rear power take-off (PTO) in high-power applications or the tractor as a transport vehicle. Operators who are looking for more power in non-stationary PTO and transport applications will be interested in the IPM feature.

 

In high rear PTO power applications such as forage harvesters, rototillers, and beet or potato harvesting equipment or where heavy trailers, carts, or implements are moved to and from various locations, this feature provides significant additional capabilities. The solution improves productivity with more consistent ground speeds, quicker acceleration, and the ability to better hold desired transport speeds.

 

This two-in-one tractor solution successfully operates in power-intensive PTO and transport applications without being disadvantaged by the extra costs of the next higher horsepower model.

 

This feature is available as a factory- or field-installed option.

Tractor applications

Rear PTO field applications

• Rear-mounted snow blowers
• Sugar beet harvesting
• Forage harvesters
• Potato harvesting
• Rotary cutters
• Mower conditioners
• Flail mowers
• Balers
• Soil stabilizing
• Power harrow
• Vegetable bed formers
• Muck spreaders

 

Transport applications

• Grain carts or wagons
• Slurry tanks
• Implement transport from field to field
• Pull-type sprayers
• Extensive operation in hills/roadways

 

This is not intended to be an inclusive list of all applications but shows the wide range of uses for additional engine horsepower.

Power available

IPM provides a controlled power boost of up to 26 engine kW (35 engine hp) to the tractor under the following operating conditions:

• Tractor moving and PTO under load
• Transport during acceleration

Power increase is not provided under draft applications or non-moving rear PTO applications.

How it works

There are specific operating parameters when IPM functions to boost engine power. It is the "intelligent" part of the system that provides seamless operation while adjusting the engine horsepower limits depending on how the tractor is being used. For engine horsepower boost activation, the tractor must be running an application that is using the full power capability of the tractor.

 

Tractor compatibility with additional power

IPM has been thoroughly tested by John Deere engineers to be compatible with the base tractor equipment with no impact to reliability. John Deere provides IPM. Unapproved aftermarket devices that boost power without regard to engine, transmission, axles, and drawbar, or hitch capability.

 

This feature provides optimal utilization of tractor components. For example, with moving PTO operation, power splits through axles to move the tractor along the ground and turn the PTO shaft and implement. Adding power to this combined system does not overload either one individually. At transport speeds, axle torque load decreases significantly from levels seen at working field speeds. Adding IPM power at transport does not overload transmissions or axles.

 

Aftermarket devices are not selective when power increases are available. Great amounts of power increase may be promised with these devices. Large power changes are not compatible with base tractor equipment. The tractor’s systems are specifically designed to ensure durability of the total vehicle as power increases. Operating outside of the design capabilities of the tractor base equipment will have an impact on durability and reliability.

 

 

Front weights provide additional ballast for the front axle

Cast Quik-Tatch suitcase weights (R127764) can be added to provide additional ballast for implements that exert heavy draft loads and require additional ballast or with hitch-mounted implements that require additional ballast to maintain steering control while transporting.

 

These weights are Quik-Tatch weights that require minimal effort to attach.

Pickup weights

Pickup weights are designed to add fast weight to the tractor. The following pickup weights can be mounted at the front.

 

Support (base weight):

• 900-kg (1948-lb) pickup weight
• 1150-kg (2535.3-lb) pickup weight

All pickup hitches can also be mounted at the rear in the 3-point hitch as a counter weight. To use the third mounting point, an additional center-link bracket is available.

 

1500-kg (3307-lb) and 1800-kg (3968.3-lb) pickup weights

 

The two weights differ only internally, therefore no external differences are visible.

 

The pickup weights can either be installed on the rear hitch or on the front hitch of the tractor using the center-link bracket. They cannot be mounted directly on the front base weight. A front hitch is required. The center-link bracket for installation is included.

The shape of the 1500-kg (3307-lb) and 1800-kg (3968.3-lb) pick-up weights allows for quick and safe mounting. This is ensured by an optimal alignment of the weight and the tractor along with a self-centering design.

 

Major benefits of the design:

• Easy and comfortable
• Less time is required
• Lower risk of injury

 

Due to the user-friendliness, an optimal ballasting of the tractor is guaranteed at any time.

 

The performance of the tractor is used to a greater extent, which leads to higher productivity and a reduction in fuel consumption.

The weights cannot be front installed in combination with Quik-Tatch front weights.

 

NOTE: Ballast should be limited by the lowest of either tire capacity or tractor capacity. The carrying capacity of each tire should not be exceeded. For more ballasting information refer to the Operator's Manual and ballast calculator.

Additional 140-L/min (37-gpm) standard flow SCVs with 12.7-mm (½-in.) couplers can be field-installed for those who need to control additional hydraulic functions. Kits include ISO lever-assisted breakaway couplers and armrest control lever. Additional SCVs can also be integrated into the Headland Management System.

 

The rear electrohydraulic SCVs with adjustable flow rates, timed detents, and breakaway couplers can be added for up to six rear SCVs. These SCVs provide metered hydraulic flow with pressure and load-sensing compensation and with load check valves to reduce leakage.

 

The tractor enables precise control of the SCV’s hydraulic flow, enabling operators to fine-tune flow rates for any application.

 

Each SCV has its own controller, making field installation of additional SCVs easier. All hydraulic settings can be adjusted through the CommandCenter™ controls and display.

Additional 140-L/min (37-gpm) standard flow SCVs with 12.7-mm (½-in.) couplers can be field-installed for those who need to control additional hydraulic functions. Kits include ISO lever-assisted breakaway couplers and armrest control lever. Additional SCVs can also be integrated into the Headland Management System.

 

The rear electrohydraulic SCVs with adjustable flow rates, timed detents, and breakaway couplers can be added for up to six rear SCVs. These SCVs provide metered hydraulic flow with pressure and load-sensing compensation and with load check valves to reduce leakage.

 

The tractor enables precise control of the SCV’s hydraulic flow, enabling operators to fine-tune flow rates for any application.

 

Each SCV has its own controller, making field installation of additional SCVs easier. All hydraulic settings can be adjusted through the CommandCenter™ controls and display.

This is a power beyond kit that can be used to assist with hooking up large equipment where multiple connections are required. The function is to supply oil to implements that have their own control valves for certain functions and do not need the controllability aspect that an SCV would give.

This is a power beyond kit that can be used to assist with hooking up large equipment where multiple connections are required. The function is to supply oil to implements that have their own control valves for certain functions and do not need the controllability aspect that an SCV would give.

Lift assist wheels are often used with heavy 3-point-hitch-mounted implements. The hitch auxiliary raise kit provides hydraulic power for use with the lift assist wheels. Turning and transport are made easier using this feature.

This is a power beyond kit that can be used to assist with hooking up large equipment where multiple connections are required. The function is to supply oil to implements that have their own control valves for certain functions and do not need the controllability aspect that an SCV would give.

Increase visibility for low light transport and for loader work by adding these lights to the front of the cab at the roofline. Lights are halogen to meet brightness requirements and mount into a fixed position bracket optimized for road use and loader work.

The LED beacon lights for model year 2020 and newer tractors have an updated look. The super low profile puck-style beacon assembly emits a very bright flashing amber light. Two pucks are mounted on the two front corners of the cab roof and a third is mounted on the center rear cab roof.

 

On tractors not configured from the factory with these high-visibility caution lights, this kit can be added, which includes the same parts used in the factory order code. Once the existing plugs have been removed from the cab roof, the beacon pucks can be connected to the existing wiring harness in the cab.

Increase light output over halogen work lights with this four-light kit for the rear corners of the mid-body cab. These lights are the same parts included in the Ultimate Visibility package and are a direct fit upgrade. Each light can be positioned side-to-side and up and down to get the maximum amount of light-emitting diode (LED) light right where it is needed most.

Increase light output over halogen work lights with this four-light kit for the front and rear roof corners of the cab. These lights are the same parts included in the Premium and Ultimate Visibility package and are a plug-and-play update. Eliminate bulb replacements while increasing color temperature and lumen output with this eight-light LED upgrade.

Upgrade the outside mirrors from the Select or Premium Visibility package with a fully electric telescoping feature and lens adjustment, as well as heating elements and wide-angle lens. This kit includes everything needed to upgrade including the control switches and power harness. Add increased visibility and ease of use with the ultimate in visibility comfort.

The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.

Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.

Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.

 

The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.

The Category 4N/3 and Category 3/3N cast Quik-Couplers provide increased clearance between an implement and the tractor’s tires and allow fast and convenient attachment to implements.

 

The Quik-Coupler is converted from a 3 to the 3N dimension by swapping the vertical arms from the wide position to a narrowed position.

 

The larger Category 4 can be converted to a Category 3 by flipping the double-sided lower hooks and exchanging the center link hook with the Category 3 hook. It is stored on the tractor frame when not in use.

Add a trailer brake system into the machine to connect the implement’s braking system safely and correctly. This kit allows operators to slow the tractor and the implement together, which is especially helpful for heavy road transport and to manage larger implements while maintaining good stopping power. Some of these kits are equipped with Auto-Detect functionality and others are not, depending on vintage of vehicle kit.

 

Always follow correct service intervals and perform required maintenance on the implement braking system by following the implement operator’s manual.

See true ground speed by adding a dual-beam radar. Select the correct mounting bracket for the tractor based on the drivetrain configuration, which includes a perfect-fit bracket, harness, and hardware.

See true ground speed by adding a dual beam radar. Select the correct mounting bracket for the tractor based on the drivetrain configuration, which includes a perfect-fit bracket, harness, and hardware.

See true ground speed by adding a dual beam radar. Select the correct mounting bracket for the tractor based on the drivetrain configuration, which includes a perfect-fit bracket, harness, and hardware.

This kit adds an additional element of safety with an audible backup alarm. It produces an audible repeating pulse tone when the tractor is placed in a reverse gear for pedestrian warning. The kit includes an alarm assembly, mounting brackets, wiring harness, and hardware.

Front idler weights add weight to the front of a track tractor to offset the weight of a hitch-mounted or drawn implement that exerts heavy loads on the rear of the tractor.

 

One pair of starter weights is required per idler to add additional wheel weights on the inside and outside of the front idler wheel.

NOTES:
1. Starter weight is required to install additional wheel weights on the idler.
2. Order attaching hardware through Parts.

Front idler weights add weight to the front of a track tractor to offset the weight of a hitch-mounted or drawn implement that exerts heavy loads on the rear of the tractor.

 

One pair of starter weights is required per idler to add additional wheel weights on the inside and outside of the front idler wheel.

NOTES:
1. Starter weight is required to install additional wheel weights on the idler.
2. Order attaching hardware through Parts.

Front idler weights add weight to the front of a track tractor to offset the weight of a hitch-mounted or drawn implement that exerts heavy loads on the rear of the tractor.

 

One pair of starter weights is required per idler to add additional wheel weights on the inside and outside of the front idler wheel.

NOTES:
1. Starter weight is required to install additional wheel weights on the idler.
2. Order attaching hardware through Parts.